Injectors and Installation Kits

Dodge / Cummins 5.9 Injector Installation Kit for1998.5 - 2003 24 Valve Applications 24V Cummins Injector Kit Includes:(6) Connector Tube O-rings(6) Injector Body O-rings(6) Copper Chamber (Tip) Gaskets Please note when purchasing this 24 Valve Cummins Injectors Installation kit, these parts should ALWAYS be replaced when your injectors are removed for any reason.

6.0L Standpipe / Front Port Plug Seal Kit fits 2004.25 - 2009 6.0L Powerstroke(also International VT275 (4.5L) and VT365) When replacing injectors on 2004.25 and later Powerstrokes (those equipped with the 'wavy' style oil rail), it is wise to replace the standpipe and dummy (front port) plug seals. These are common leakage points in the high pressure oil system and can cause hard starting, especially when hot. This kit contains the necessary parts to re-seal both cylinder heads and will...

6.2L and 6.5L Intake Gasket SetThis set includes a pair of lower intake gaskets, upper plenum gasket (for 6.5L), air cleaner base gasket (6.2L), and the pump flange gasket. This is the kit you need to change the injection pump on your 6.2/6.5 diesel. Note that the lower intake gaskets includes metal block off plates to eliminate EGR (off-road only) which has many advantages on these engines. If you wish to retain EGR, simply remove the plates ...

6.2L / 6.5L Injection Lines Complete set of eight brand new fuel injection lines for Chevy / GMC / CUCVEE 6.2 Diesel engines. These fuel injection lines are specifically intended for 1988.5 to 1993 engines (with short injectors). They can also be used on 1982 - 1988.5 vehicles in place of the (no longer available) early 6.2L Injection lines. They will require very minor "tweaking" at the injector end to make them fit. These are also the lines you need if you are converting from electronic to...

GM 6.2L / 6.5L Diesel Injector Installation Kit This diesel injector kit includes copper washers, clamps, plenum / air cleaner gaskets, return lines and end caps. These self-sealing lines do not require clamps which will save you installation time and hassle. A must when changing your injectors! This high quality injector kit is Made in Germany

Genuine OEM Pure Power Reman 6.4L Ford Powerstroke Fuel Injector(includes NEW injection line)fits2008 - 2010 6.4L Powerstroke injectors are a very demanding application and time has shown that genuine OEM remans are a better choice than anything offered by the aftermarket, so we have chosen to offer the OEM product for greatest reliability. Unlike previous Ford 6.4 diesel injectors, which were controlled by magnetic solenoids, the Siemens injectors used in 2008 - 2010 Powerstrokes are a piezo...

For those who truly appreciate the best quality and will settle for no substitutes, we are now offering genuine brand NEW Bosch diesel injectors. Bosch is the OEM manufacturer of the injectors for the 6.5L diesel engine. 6.5 Diesel Injectors Applications: 1992 - 2005 Chevy or GMC 6.5L Turbo diesel. 'Tune-up' Kits: We have put together a package that includes a set of our Premium USA-Made glow plugs, an injector installation kit, and a set of new injectors. It often makes sense from a labor...

6.9L / 7.3L IDI Pump / Injector Install Kit Fits 1983 - 1994 Our 6.9 / 7.3 IDI injector & pump installation kit includes plastic return fittings, injector o-rings and washers, return line, clamps, and line seals. If any of your return lines or connections leak, the injection pump will 'bleed back' and the truck will be very hard to start after sitting. It may briefly start and then stall requiring very long crank times to re-prime the pump. You may select injector installation kit only below,...

6.9L / 7.3L IDI Injection Lines Complete set of eight brand new fuel injection lines for Ford 6.9 / 7.3 IDI and/ International T444 engines from 1982 - 1994 both turbo and non-turbo. If you are rebuilding your engine or replacing your pump, now is a great time for new 6.9 Diesel & 7.3 IDI injector lines - injection lines do occasionally rupture and can leave you stranded. Trucks in northern states usually exhibit very rusty and pitted lines further worsening the situation. Failure to install...

- 7.3L Powerstroke Injectors - One Year Unlimited Mileage Warranty! These Ford 7.3 Powerstroke diesel injectors are remanufactured by one of the most experienced shops in the business with over 30,000 Powerstroke injectors rebuilt to date, and are second to none. Don't shop on price alone when buying HEUI Injectors! New Alliant Power (OE) external o-rings are included with injectors for 7.3 Powerstroke vehicles. After the rebuilding process, each Ford 7.3 Powerstroke injector replacement is...

- BRAND NEW - Fuel Injector Solenoid Fits: 2001 - 2004.5 Duramax LB7 Injector Solenoid or 2003 - 2007 Dodge / 5.9 Cummins Injector SolenoidIf your injector has a broken electrical stud or if the injection pump solenoid is shorted or open circuit, you do not have to replace the entire injector. This fuel injector solenoid is designed to easily replace your old one. Just loosen the retaining nut, lift the old solenoid off, set the new one on and re-tighten the nut to approximately 15 ft-lbs. Be...

Mechanical Diesel Injector Testing Service The price of this diesel injector testing service includes testing for up to 8 diesel injectors. We will test your 8 mechanical diesel injectors and provide you with an honest assessment of their condition. Tests will include pop pressure, leakage, chatter, etc. Also inlcuded in the price is return shipment via Priority mail with $100 of insurance. You may add additional insurance if desired. Injectors we will test include GM 4.3L, 5.7L, 6.2L, and...

2001 - 2004 Duramax LB7 Injector Installation Kit This Duramax injector installation kit includes the following essential parts for replacing your injectors: 16 External injector o-rings (2 for each injector)8 Tip washers8 joined banjo washer pairs for connecting return lines to each injector2 joined banjo washers for connecting the return line on each side to the head. This LB7 injector kit includes enough parts to install all 8 injectors. In addition to this LB7 injector replacement kit, we...

LBZ Fuel Injector fits 2006 - early 2007 Duramax Diesel with LBZ Engine Genuine OEM Bosch LBZ injectors for sale - remanufactured by Bosch (To verify that you are purchasing the correct Bosch fuel injector please check that the eighth digit of your VIN is a "D") Each LBZ Duramax injector comes with the body o-ring and copper tip gasket ready for installation. Also included is a sheet with the injector flow calibration number to be programmed into the PCM and glow plug control module at time of...

LLY Fuel Injector fits 2004.5 - 2005 Duramax Diesel with LLY Engine Genuine OEM Bosch Reman NOT an aftermarket reman! (Please note that some 2004 Duramax engines use the LB7 engine and a different injector. To identify your engine, check the eight digit of the VIN - if you have an LLY engine, it will be a "2") Each 2004.5 - 2005 Duramax LLY injector replacement comes with the body o-ring and copper tip gasket ready for installation. We also sell brand new stock injectors and performance LLY...

LLY Fuel Injector fits 2004.5 - 2005 Duramax Diesel with LLY Engine BRAND NEW Genuine OEM Bosch LLY Duramax Injector - NOT remanufactured (Please note that some 2004 Duramax engines use the LB7 engine and a different injector. To identify your engine, check the eight digit of the VIN - if you have an LLY engine, it will be a "2") Each Duramax LLY injector replacement comes with the body o-ring and copper tip gasket ready for installation. We also sell performance LLY injectors - see related...

2004.5 - 2010 Duramax Injector Kitworks for Duramax LBZ, LMM, & LLY injector replacementIncludes:(8) Copper Chamber / Tip Gaskets / Washers(8) Injector Body O-ringsThese parts are essential to replace every time your injectors are removed.Replace the following part numbers:Tip Gasket - Bosch: F00RJ01086, GM: 97327722O-ring - Bosch: F00E200099, GM: 94013303 ...

DURAMAX LLY LBZ and LMM Injector Return Rail Kit D660023 FUEL RAIL RETURN LINE KIT INCLUDES: (3) 'T' return connectors(1) 90 degree return connector(4) Return connector O-rings(4) Return connector retaining clips (GM P/N 97359750)Return Line Hose sufficient for one side This Duramax fuel return line kit includes enough parts to service one side of the engine and works on either the left or right side. Purchase (2) fuel rail return line kits to service both sides (Discounted price of...

DURAMAX LLY LBZ and LMM Injector Return Rail Kit with METAL FITTINGS INCLUDES: (6) 'T' return connectors(2) 90 degree return connector(8) Return connector O-rings(8) Return connector retaining clips (GM P/N 97359750)Return Line Hose Tired of plastic return fittings? This kit includes one-piece metal fittings - no more broken plastic fittings. Our return hose is a carefully selected high-grade diesel-rated hose made in Europe. This Duramax injector return line kit includes enough parts to...

6.9L / 7.3L IDI FORD / International - Remanufactured Injectors - (and "Tune-Up Kits") fit 1983 - 1994 Non-Turbo Typically by 100,000 miles IDI injectors are worn and new injectors will increase efficiency / fuel economy and reduce smoke. These Ford 6.9/7.3 remanufactured injectors are second to none. New tip gaskets and return o-rings are included. An additional core charge of $100 is required which will be refunded when we receive your old Ford injectors. You may also wish to purchase our...

6.2L "Short" Injector Set Premium Remanufactured These remanufactured 6.2 diesel injectors are second to none. In fact, analysis on a sophisticated injecto-matic machine has repeatedly shown that our remanufactured injectors perform better than many new injectors. Because some who market new injectors have spread mis-information about remanufactured injectors, many have been led to believe that re-manufactured injectors are inferior. To the contrary, we find that many of the new GM 6.2L...

6.5L Turbo Diesel Injectors - REMANUFACTURED - fits 1992 - 2005 Chevy / GMC / H1 / Humvee These remanufactured 6.5 turbo diesel injectors are second to none. In fact, analysis on a sophisticated injecto-matic machine has repeatedly shown that our remanufactured diesel injectors perform better than many new injectors. Because some who market new injectors have spread mis-information about remanufactured diesel injectors, many have been led to believe that re-manufactured injectors are inferior....

- LB7 Duramax -Fuel Injection Line Setfits 2001 - 2004.5Injection line corrosion is a huge problem on the LB7 Duramax diesels - especially in northern states. Water tends to collect inside the nut at the injector end of the line causing rust to form. When the injection line is removed, the inlet of the injector becomes filled with rust particles. Many times when we receive core injectors back from our customers the injector inlet is completely blocked with rust. The greatest problem is that if...

6.0 Blue Spring Upgrade Kit for2003 - 2010 Ford 6.0L Powerstroke Diesel(and International VT275 / 365) FAQ's: 'What is the purpose of this kit?'According to Ford the most common cause of 6.0L injector failure is low fuel pressure. The 6.0 Powerstroke blue spring kit increases the pressure to your injectors by about 10%. Every 6.0L owner should perform this inexpensive upgrade! 'Will this kit damage my engine?'Absolutely not - this kit was not our idea. Ford developed the blue spring update and...

Dodge / Cummins 5.9/6.7L Dodge/Cummins Common Rail Injector Installation Kit for2003 - 2016 Applications INCLUDES:(6) Connector Tube O-rings(6) Injector Body O-rings(6) Copper Chamber (Tip) Gaskets These parts should ALWAYS be replaced when your common rail injectors are removed for any reason. We also carry 5.9L and 6.7L Common Rail Injectors, connector tubes, CP3 Pumps, and much more! ...

Performance Injector Nozzle Set Fits 24 Valve 5.9L Cummins 1998.5 - 2002 Looking to add a few more HP to your Cummins? With our performance VCO injector nozzle sets you can build your own set of oversize injectors and save $$. We offer multiple sizes to suit the needs of your particular build. (Select the size you need from the drop-down below.)We also offer our own pop-test adapter to aid in checking your injectors before installing them - see related items below. ...

GENUINE S&S Diesel Motorsport 5.9L Cummins Diesel Injectors - Available in NEW or Remanufactured - 60 HP, 100 HP, and Larger! For those customers who are seeking the very best performance injectors on the market, we are pleased to offer genuine S&S Diesel Motorsport Fuel Injectors. S&S is in a unique class at the top of the industry for their integrity and commitment to doing things right. When second best will not do, chose #SSfueled - Incorporating all of the most recent updates for maximum...

5.9L Dodge Fuel Injector - fits 2003 - 2004.5 - Notes: - All 5.9 Cummins injectors come with NEW O-rings and tip gaskets included. -If your truck is a 2004, please check the engine data tag to verify that you are ordering the correct injector. These injectors are for trucks with a 235, 250, or 305 HP rating. If you need the later injector, please see the related items at the bottom of the page. Option 1 $235 each plus Core Premium Remanufactured Injector- Not just repaired - Remanufactured to...

5.9L Dodge Fuel Injector - fits 2004.5 - 2007 - Notes: - All 5.9 Cummins and Dodge fuel injectors come with NEW O-rings and tip gaskets included. - If your truck is a 2004, please check the engine data tag to verify that you are ordering the correct injector. These injectors are for trucks with a 325 HP / 600 ft-lb rating. If you need the earlier injector, please see the related items at the bottom of the page. Option 1 $235 each plus Core Premium Remanufactured Injector- Not just repaired -...

GENUINE S&S Diesel Motorsport 5.9L Cummins Diesel Injectors - Available in NEW or Remanufactured - 60 HP, 100 HP, and Larger! For those customers who are seeking the very best performance injectors on the market, we are pleased to offer genuine S&S Diesel Motorsport Fuel Injectors. S&S is in a unique class at the top of the industry for their integrity and commitment to doing things right. When second best will not do, chose #SSfueled - Incorporating all of the most recent updates for maximum...

BRAND NEW5.9L COMMON RAIL INJECTION LINES- Set of 6 - FITS:2003 - 2007 Dodge 5.9L Cummins DieselOwn a 5.9L Cummins common rail engine? One disadvantage of common rail is that if you break one injection line, you are dead in the water! At this price, it might well be worth it to have an extra set under the seat! If your common rail fuel lines are rusty or you have already broken one, it might be wise to replace them all and keep the others for spares. Each Dodge Cummins fuel line comes complete...

6.0L FORDPOWERSTROKE- Internal Injector Parts Kit -FITS:2003 - 2010 If you are repairing your own 6.0L injectors, this kit will supply you many of the internal 6.0 Powerstroke injector parts that are often overlooked and can be very difficult to find. - Intensifier Piston- Plunger- Intensifier Piston Spring- Nozzle Spring- Nozzle spring support- Plunger Spring Retainer- Steel Upper Dring Spacer- Lift Spacer Each kit services (1) Injector. ...

6.0L Powerstroke Diesel Injector Seal Kit all years 2003 - 2007 (also fits International 4.5L VT275/365)Complete kit - enough parts for 8 injectors- Injector Seal Kit Includes -(per injector)(2) Connector O-rings (outer and inner)(2) Injector Body O-rings(1) Copper Crush Gasket for injector tip(1) Upper D-ring Seal (located in top of injector - seals high pressure oil rail nipple to injector)(1) D-ring retention snap ring(2) Internal Injector O-rings (Not normally used unless injector is being...

6.0L Powerstroke - 30% Over - PERFORMANCE FUEL INJECTOR These 6.0 Powerstroke performance fuel injectors start life as genuine OE remanufactured parts - direct from Ford's original equipment supplier - the very best remanufactured injector available. The nozzle is then carefully removed, extruded honed to 30% over, and replaced retaining the benefits of having a reman injector with 100% OEM parts. These 6.0 Powerstroke performance fuel injectors deliver 30% over - an upgrade that typically...

6.0L Powerstroke - 30% Over - BRAND NEW PERFORMANCE FUEL INJECTOR These 6.0 Powerstroke performance injectors start life as genuine OEM BRAND NEW  parts - direct from Ford's original equipment supplier - the very best  6.0L Injectors available. The nozzle is then carefully removed, extruded honed to 30% over, and replaced retaining the benefits of having an injector with 100% new OEM parts. These Ford 6.0 performance injectors deliver 30% over - an upgrade that typically yields...

BRAND NEW6.0L Powerstroke- SPOOL VALVE SET - (fits 2003 - 2010)Are your injectors experiencing Stiction?It is well-known that a large percentage of the difficulties experienced with the infamous 6.0L injector originate in the spool valve. Many customers have been disassembling their own injectors and cleaning the spool valves in an attempt to restore normal operation. However, with the increasing age and mileage of the 6.0L Fleet, it is often found that the spool valves are badly scored or...

6.0L Powerstroke Injector Steel Spacer Fits 2003 - 2010 The 6.0L Powerstroke fuel injector has a D-ring style rubber seal in the top of the injector where the high pressure oil rail ball tube plugs into the top of the injector. The D-ring seal in the injector is retained by a snap ring, below the snap ring is a beveled steel spacer that guides the high pressure oil rail ball tube squarely into the D-ring seal. From time to time, a catastrophic failure occurs at this seal point and the steel...

6.0L Early High Pressure Oil System Seal Kit fits 2003 - early 2004(ONLY systems with aluminum high pressure oil pump and tubular oil rails) It is advisable to purchase this Powerstroke HPOP seal kit when installing fuel injectors or a 6.0 high pressure oil pump.We have seen many HPOP's wrongly blamed for starting issues resulting from leaks in the high pressure oil plumbing on early 6.0L's.The High Pressure oil line disconnect tube (see related items below) is very helpful for disconnecting...

AccurateDiesel.com now offers two remanufactured Ford 6.0 injector replacement options - read about them in detail below along with diagnostic and installation information. Our unlimited mileage warranty runs circles around the 12,000 miles offered by our largest competitors. 6.0L injectors are a demanding application - we provide you with the highest quality injectors for 6.0 Powerstroke diesels at very competitive pricing. Please note that we now offer brand NEW 6.0 Powerstroke Injectors....

BRAND NEW - Genuine OEM Pure Power - 6.0L Powerstroke Injector NOT Remanufactured! For many years our customers have asked us for a BRAND NEW 6.0L Powerstroke Injector Option. Finally, it is here! Our new fuel injectors come direct from Ford's original equipment supplier. There is simply no better 6.0L injector anywhere on the planet. For those who appreciate the very best quality, this is it. No part of the injector ever used in any engine anywhere at any time! Please note that the...

- 6.0L Injector Connector Body - fits2003 - 2010 Ford 6.0 Powerstroke These Ford fuel injector connector replacements have been difficult to obtain for a long time - they are finally available at a reasonable cost. No need to replace the entire injector just because of a broken connector body. The tabs that hold this Ford 6.0 injector connector into the rocker housing often break off (sometimes due to improper service technique). When this occurs, the injectors are prone to becoming unplugged...

- 6.0L Powerstroke Fuel Injector Solenoid Set -FITS2003 - 2010 Ford Powerstroke(Also 4.5L VT275 / VT365)Are you getting high or low injector circuit codes?If you have checked the injector wiring / connections and FICM the remaining possibility is the injector coils.This fuel injector solenoid set includes both open and close coils. These are easily changed in a matter of a few minutes and can save you the price of an injector.BULK DISCOUNTS AVAILABLE ...

BRAND NEW 6.0L Powerstroke- Performance Nozzle Kit - INCLUDES:- (8) 30% over injector nozzles- Complete Internal and External Injector Seal Kit- Injector Holding FixtureOur 30% over stock 6.0 Powerstroke performance injector nozzle kit includes everything that you would normally need to upgrade your fuel injectors. The 30% over upgrade typically yields around a 70HP increase on an otherwise stock truck. Many customers also report better fuel economy, although this varies with driving...

BRAND NEW 6.0L Powerstroke- Stock Nozzle Kit - INCLUDES:- (8) Stock 6.0 Powerstroke injector nozzles- Complete Internal and External Injector Seal Kit- Injector Holding FixtureTime to freshen up your 6.0L Injectors? Fuel injector nozzles are a wear item that will degrade in performance over time causing decreased atomization quality leading to lower combustion efficiency, smoke, and decreased economy. Replacing fuel injector nozzles is a fairly simple / basic process requiring only a few...

6.0L Ford Powerstroke- Upper Valve Cover Gasket - (Includes Grommets and Crankcase Breather Seals)Fits:2003 - 2010 Ford Powerstroke- Trucks, Vans, and Excursions - This 6.0 Powerstroke valve cover gasket is also available as a set for $36.95 - select the option below ...

BRAND NEW 6.2L / 6.5L Diesel Fuel Injector Socket - MADE IN THE USA - Why a special socket for the 6.2 / 6.5 Injectors? 1. The special socket is shaped on the inside to hold the injector correctly and prevent the injector from getting crooked inside the socket. When using a standard socket, the injector return nipples are often bent over when the injector and the socket get at an angle to one another while working in confined spaces. Many times the return connections can not be straightened...

2008 - 2010 Ford Powerstroke 6.4L Injector Seal Kit Includes:(8) Copper Chamber / Tip Gaskets / Washers(8) Injector Body O-rings This 6.0 Powerstroke injector o-ring kit includes the parts that are essential to replace every time your injectors are removed. Replaces the following part numbers: 8C3Z9229A (w/o line)

BRAND NEW 6.4L PowerstrokeINJECTION LINE FITS2008 - 2010 6.4L Powerstroke The OEM requires that anytime 6.4 injection lines are removed or loosened, they MUST be replaced. Fuel system pressure on the 6.4L maxes out at nearly 25,000 PSI and even the tiniest leak will cause oil dilution and possible engine damage due to the under-the-valve-cover location of the fuel injector and line assembly. Don't risk catastrophic engine failure by re-using old lines. 6.4 Powerstroke fuel lines replace the...

BRAND NEW 6.4L Powerstroke Injector Installation KitINCLUDES:- Injection Line- Injector Tip Gasket- Injector body O-ring FITS2008 - 2010 6.4L Powerstroke The OEM requires that anytime the injection lines are removed or loosened, they MUST be replaced. Fuel system pressure on the 6.4L maxes out at nearly 25,000 PSI and even the tiniest leak will cause oil dilution and possible engine damage due to the under-the-valve-cover location of the fuel injector and line assembly. Don't risk catastrophic...

6.4L Ford Powerstroke- Fuel Injector Harness Set -fits2008 - 20106.4L Ford Powerstroke and Navistar MaxxForce 7Includes Left and Right SidesReplaces the following part numbers (and others):1856010C95 1856011C95 8C3Z9D930AA 8C3Z9D930BA

6.5L Injection Lines Complete set of eight brand new fuel injection lines for GM 6.5 Engines equipped with electronic injection pump (will not fit mechanical pump). If you are rebuilding your engine or replacing your pump, now is a great time for new 6.5 diesel injector lines - injection lines do occasionally rupture and can leave you stranded. Trucks in northern states usually exhibit very rusty and pitted lines further worsening the situation. Failure to install all of the...

6.5L Fuel Injectors fits 6.5L Chevy / GMC / HUMVEE / H1 1992 - 2005 also "Tune Up" Kits Avoid the hassle of returning cores with our brand new injectors. We have tested and examined 6.5L injectors from every manufacturer on the globe. We believe these to be in the top tier of aftermarket 6.5 injectors. Their fit and finish is very good and much more assuring of inner quality than many of the competitive parts we have examined. When should 6.5L injector nozzles be changed? Generally speaking,...

6.7L Cummins NEW OEM Bosch Injector Applications: 2007 - 2012 Dodge truck w/ 6.7L engine Notes: - These are BRAND NEW Dodge Cummins Injectors - NOT remanufactured! Unquestionably the best 6.7L injector money can buy. - All 6.7 Cummins Injectors come with NEW O-rings and tip gaskets included. - These are pickup injectors. Cab / Chassis trucks require a different injector. These injectors replace the following Bosch, Dodge, and Cummins part numbers (and others): 0445120193, 0986435518,...

6.7L Cummins NEW OEM Bosch Injector Applications: 2013 - 2018 Dodge pickup w/ 6.7L engine Notes: - These are BRAND NEW OEM Dodge Cummins Injectors - NOT remanufactured, NOT Aftermarket! Unquestionably the best 6.7L injector money can buy. - All 6.7 Cummins Injectors come with NEW O-rings and tip gaskets included. - These are pickup injectors. Cab / Chassis trucks require a different injector. These injectors replace the following Bosch, Dodge, and Cummins part numbers (and others): 0445120342,...

6.7L Cummins Injector REMANUFACTURED Applications: 2007 - 2012 Dodge Pickup w/ 6.7L engine - These 6.7 Dodge Cummins Fuel Injectors are not just repaired or refurbished. They are remanufactured in a production environment where rigid quality standards and exacting procedures are maintained. ONLY OEM BOSCH parts are used. NO Aftermarket parts. We have determined that one of the most critical factors in building a quality injector that will stand the test of time is to use Bosch parts. - Cummins...

GENUINE S&S Diesel Motorsport 6.7L Cummins Diesel Injectors - Available in NEW or Remanufactured - 60 HP, 100 HP, and Larger! For those customers who are seeking the very best performance injectors on the market, we are pleased to offer genuine S&S Diesel Motorsport Fuel Injectors. S&S is in a unique class at the top of the industry for their integrity and commitment to doing things right. When second best will not do, chose #SSfueled - Incorporating all of the most recent updates for maximum...

6.7L FORD POWERSTROKE FUEL INJECTION LINEFITS CYLINDER 1, 2, 7, 8 Ford requires that the 6.7 Powerstroke fuel lines be replaced any time they are loosened or removed for any reason.6.7L engines use two different injection line types with slightly different bends. If you need a line for a cylinder not mentioned above or a full set, please see related items below. ...

6.7L FORD POWERSTROKE FUEL INJECTION LINEFITS CYLINDER 3, 4, 5, 6 Ford requires that the 6.7L diesel injector fuel lines be replaced any time they are loosened or removed for any reason.6.7L engines use two different fuel injector line types with slightly differentbends. If you need a line for a cylinder not mentioned above or a full set, please see related items below. ...

6.7L FORD POWERSTROKE FUEL INJECTION LINE SET(8 pieces) Ford requires that the 6.7L diesel injector fuel lines be replaced any time they are loosened or removed for any reason.This fuel line set consists of two types of lines - four pieces of each. One type fits injectors 1, 2, 7, and 8. The other type fits injectors 3, 4, 5, and 6. There is a noticeable difference in the bend of the line between the two types. ...

Remanufactured6.7L Ford Powerstroke Injector- Genuine OEM Bosch - FITS2011 - 2014 We are most comfortable recommending genuine OEM Bosch injectors, remanufactured by Bosch, for your 6.7L Powerstroke application. Pricing is very favorable compared to aftermarket options and considering the high stakes involved on the 6.7L application, we feel it is wise to go with the best available part.When replacing 6.7L Powerstroke injectors, Ford also requires that the fuel injection lines be replaced -...

FORD6.7L PowerstrokeInjector Return FittingFits:2011 - 2019 Note: This listing is for (1) Fitting, (1) Foot of hose, and clamps. Three fittings are shown above. You will need to select the fitting you need from the options below when purchasing. Were you replacing an injector and accidentally broke a fuel injector return line connector? It is very easy to do as they are plastic and when they get full of grit and grime can be very challenging to release. In the past, your only option was to buy...

2011 - 2019 Ford Powerstroke 6.7L Injector Seal Kit Includes:(8) Copper Chamber / Tip Gaskets / Washers(8) Injector Body O-rings (8) Return line Fitting Orings These hard-to-find parts are essential to replace every time your injectors are removed.Replace the following part numbers:BC3Z9229A (w/o line)

- BRAND NEW - IDI Injector Set fits 1983 - 1994 6.9L / 7.3L IDI Non-turbo - Set of 8 - New return o-rings and copper chamber gaskets included. NOTE: This 6.9 / 7.3 IDI injector set will NOT fit 1994 and newer Powerstroke diesels - see  our full Powerstroke Diesel Parts category We also carry 7.3 IDI injector return line kits, which are a good investment, they make installation a lot easier, and prevent return line leaks which cause hard starts. Additionally, we offer a...

7.3L Powerstroke External Oring Set This kit is made by Alliant Power - the OE manufacturer for Powerstroke injectors. There may be a place to skimp on parts, but it is not here. It takes some effort to replace these o-rings and if they leak there are a number of symptoms you may experience such as hard starting, horrible oil consumption, engine miss, smoke, etc. Take our advice and buy only the best external o-rings for your Powerstroke injectors! Ford has spent years re-designing the number,...

1994 - 2003- 7.3L Ford / International T44E Powerstroke Diesel - Used Fuel Injector Oil Spill Spout with bolt Did you loose or break an injector oil spill spout on your Ford?These are in great condition - much cheaper than the dealer!

NEW 7.3L Powerstroke Injector Solenoid- Fits All 1994 - 2004 7.3L Ford / International Powerstroke and T444E -This solenoid commonly fails causing the injector not to operate or fail a buzz test. Check the resistance of each solenoid to locate failed or failing solenoids.

BRAND NEW 100 HP PERFORMANCE INJECTORS - 7 x .009 - 25% Flow Increase (set of 6) 1998.5 - 2002 Dodge / Cummins Fuel Injectors FAQ's: What does "7 x .009 mean? Each Dodge Cummins 100HP injector tip has 7 holes through which fuel is injected. Each hole is 9 thousands (.009) inches in diameter. What horsepower gains can I expect? Depending on what other modifications your truck is equipped with, overall state of tune, engine health, injection timing setting, etc gains of 100 HP at the flywheel...

BRAND NEW RV275 MILD PERFORMANCE INJECTORS - 7 x .008 - (set of 6) 1998.5 - 2002 Dodge / Cummins FAQ's: What are "RV275" Injectors? RV275 Injectors are the largest injector offered as a factory option for a 5.9L 24 Valve / VP44 pump engine. They were used in mid-range (medium duty) applications only and were not originally offered for pickup applications. RV275 injectors are a very popular upgrade for pickup owners looking for a very mild performance upgrade and are generally considered to add...

Fits 2003 - 2007 Dodge / Cummins Diesel Genuine NEW Bosch Fuel Injector Connector - Made in Germany - Includes New O-ring The 5.9 Cummins connector tube is responsible for transferring fuel from the injection line at the outside of the cylinder head to the fuel injector which is located in the center of the cylinder head. The connector tube fits into a tapered opening in the injector and forms a metal-to-metal seal. Fuel injector connection leakage is a common problem, which causes hard start...

INJECTOR CONNECTOR TUBES Applications2007.5 - 2018 6.7L Dodge / Cummins Diesel Genuine NEW Bosch Parts - Made in Germany - Includes New O-rings The connector tube is responsible for transferring fuel from the injection line at the outside of the cylinder head to the fuel injector which is located in the center of the cylinder head. The connector tube (also called a feed or cross tube) fits into a tapered opening in the injector and forms a metal-to-metal seal. Leakage here is a common problem...

Dodge 6.7L Cummins Fuel Injection Line Set 2007 - 2018 (6 Injector Lines) BRAND NEW6.7L CUMMINS COMMON RAIL INJECTOR LINES- Set of 6 - FITS:2007 - 2018 Dodge 6.7L Cummins DieselOwn a 6.7L Cummins common rail engine? One disadvantage of common rail is that if you break one injection line, you are dead in the water! At this price, it might well be worth it to have an extra set under the seat! If your common rail fuel lines are rusty or you have already broken one, it might be wise to replace...

Injection Line Set 5.9L Dodge Cummins Fits 1994 - 1998.5 Assembled with Clamps This injection line set fits the P7100 aka "P-pump" 6BT engines. For later trucks with VP pumps see related items below. Keep your venerable Dodge on the road with a complete set of new injector lines! 12 Valve Dodge Cummins Injector Lines Replace Part Numbers: 3925810, 3925805, 3925806, 3925807, 3925808, 3925809 ...

BRAND NEW DIESELFUEL INJECTION LINE SET - Cummins Fuel Lines Assembled with Clamps - - (6) Pieces - FITS:Dodge / Cummins Dieselwith VP44 Injection Pump1998.5 - 2002 These are the (6) lines that run from the injection pump to the fuel injectors. Got rusty lines? Replace them and make your truck reliable again! These 24V Cummins injector lines are assembled with clamps for quicker, easier installation. Replaces the following part numbers:3943765, 3943773, 3943767, 3943771, 3943775, 3943769 ...

BRAND NEW DIESELFUEL INJECTION LINE SET - (6) Pieces - FITS:Dodge / Cummins Dieselwith VP44 Injection Pump1998.5 - 2002 These are the (6) lines that run from the injection pump to the fuel injectors. Got rusty lines? Replace VP44 injector lines and make your truck reliable again! Replaces the following part numbers:3943765, 3943773, 3943767, 3943771, 3943775, 3943769 ...

Navistar / International DT466 / DT530 / DT466E / I530 / HT530 Fuel Injector Seal Kit Fits 1994 - 2003  This fuel injector seal kit is offered for the first generation HEUI DT466 series engines. This fuel injector oring kit will not fit the early mechanical injector DT466, or the 2004 and newer G2.9 style injectors. Compare your injectors to those in the picture. They should look like a 7.3L Powerstroke injector with a two pin electrical connection and be located under the engine's valve...

G2.9 Injector Seal Kit- Complete for 6 Injectors - Includes:- Injector Body O-rings (2 per injector)- Tip GasketsFITS:2004 - 2017 Navistar DT466DT570MaxxForce DTMaxxforce 9Maxxforce 10Maxxforce N9Maxxforce N10Replaces Part Numbers:1842624C92, AP0026IMPORTANTThis listing does NOT include an injector. The injector picture is shown to illustrate the type of injector that this fuel injector o-ring kit is used with! ...

DT466 Mechanical InjectionInjector / Injection Pump Installation Kit- Includes all gaskets, seals, hose, clamps, washers, etc normally required when replacing the pump and fuel injectors -

LB7 Duramax Injector Fuel Return Banjo Bolts Brand new complete set of eight. These LB7 banjo bolts connect the fuel return rail under the valve cover to the fuel injectors. The allen head has a tendency to strip out during removal as in the picture below. Note the plier marks around the exterior where our customer was forced to use vise grips during removal. Re-using a stripped or partially stripped bolt is dangerous because if proper torque is not achieved an internal fuel leak will develop...

LB7 / LLY Duramax FICM Banjo Washer Set fits 2001 - 2005 LB7 and LLY Duramax route the fuel lines to the engine through the Fuel Injection Control Module (FICM) for cooling purposes. Anytime the lines are removed (such as when replacing injectors) the washers should be replaced to prevent fuel leaks. The factory uses a joined upper/lower washer for installation convenience, but they are bare steel. Our rubberized fuel injector washers create a more reliable seal. Our kit includes (4) washers...

LB7 DuramaxLower LB7 Duramax Valve Cover Bolt Set Complete Set for BOTH Sides fits 2001 - 2004.5 LB7 Duramax Diesel Valve Cover bolts incorporate an Allen head and are notorious for rounding out during the removal process. It is advisable to void re-using partially stripped hardware which will only make the process that much more difficult the next time around! Our lower valve cover / rocker box bolts incorporate an external hex head which is much stronger and less likely to strip plus being...